Airgun Talk

Airgun Moderators: How They Work and How to Choose One

7 min read

An airgun moderator is a can that threads onto the muzzle of an air rifle or pistol and quiets the report of the shot. Depending on where you live and who you ask, it's called a moderator, an airgun suppressor, a silencer or an LDC (lead dust collector). They're all the same part. In our own test, a shot that read 84.4 dB at 10 feet from the muzzle dropped to 68.1 dB with one of our airgun suppressors on, a 16.3 dB drop.

This guide covers where airgun noise comes from, how a moderator takes it down, and how to pick one that fits your gun. Fitment is where most people get stuck, so there's a full section on it, including what to do if your barrel has no threads.

Airgun Capital airgun suppressor on an air rifle barrel, with pellet tins behind it

Where air rifle noise comes from

An airgun shot makes noise in three places, and a moderator only deals with one of them.

  • Muzzle blast. The pellet leaves the barrel with a column of high pressure air behind it. That air dumps into the open all at once, and on a PCP the pop you hear is mostly that. This is the part a moderator handles.
  • The action. On a springer, the spring and piston slamming forward make a lot of the noise, and that happens inside the gun. On a PCP, the hammer hitting the valve makes a smaller click. A moderator does nothing for either.
  • Sonic crack. A pellet going faster than the speed of sound, roughly 1,100 fps, makes its own small sonic boom until it slows below the speed of sound. No moderator can stop that. If you want quiet, keep the pellet subsonic.

That's why the same moderator can sound completely different on two guns. A regulated PCP shooting subsonic gets most of the benefit. A magnum springer gets less, because a big share of its noise never comes out of the muzzle. There's more on the numbers in How Loud Is an Air Rifle? Airgun Decibels Explained.

How an airgun moderator works

The job is to stop that air column from hitting the open air all at once. A moderator gives the air room to expand and slows it down before it gets out, so it leaves at a lower pressure and makes a softer sound.

Inside the tube is a stack of baffles, which are discs with a hole in the middle for the pellet. The pellet goes straight through the holes. The air behind it gets caught in the chambers between the baffles, swirls, loses speed, and bleeds out the front over a longer stretch of time. More internal volume gives the air more room to slow down, which is why a bigger body is quieter on a high powered gun.

The hole at the front matters as much as the stack. The exit bore has to be bigger than the pellet so nothing touches it, but every bit of extra clearance is a gap the air can leak straight out of. That's why every one of ours ships with a front endcap matched to your caliber, with the exit bore within roughly 1mm of the projectile, instead of one big hole that works for everything.

Airgun moderators can be built lighter than firearm suppressors because there's no burning powder. The air is cool and the pressure is a fraction of a gunshot, so aluminum works fine. Ours are CNC-machined from 6061-T6 aluminum and hard anodized. What an airgun does throw into the moderator is lead, which is where the LDC name comes from, so being able to take it apart and clean it matters.

How much quieter will my gun get?

In the test above we measured a 16.3 dB drop at 10 feet. Decibels are logarithmic, so every 10 dB is ten times the sound intensity, and a 16 dB drop is a big difference in a backyard. Your number depends on the gun more than anything else.

  • Power. More foot-pounds means more air per shot. A low power .177 gets very quiet on a slim moderator. A full power .30 needs a lot more volume to get to the same place.
  • Shroud. A gun that already has a shrouded barrel is quieter to begin with, so a moderator still helps, but the drop is smaller than on a bare barrel.
  • Springer or PCP. See above. The muzzle part of the noise is what goes away, and on a springer that's a smaller share.
  • Velocity. If the pellet is supersonic, the crack stays no matter what.

How to choose an airgun moderator

Go in this order. Thread comes first because it decides what can even go on your gun.

1. Match the thread

Airgun muzzle threads aren't standard across the industry. Most small bore guns sold in the US use 1/2-20 UNF. Big bores vary more, and M18×1 is the most common there. You'll also run into M14×1.25, M20×1 and 1/2-28 UNEF. A moderator cut for your exact thread threads straight on and sits square to the bore. One that's close but not right will bind a couple of turns in and can gall the threads on your barrel.

Check your owner's manual or the manufacturer's spec sheet before you order. If you can't find it there, Airgun moderator thread sizes: how to identify your barrel pitch walks through every other way to find it.

2. Size it to your caliber and power

Pick by the largest caliber you plan to shoot, then think about power. A slim body is plenty for .177 through .25 at moderate power and keeps weight off the muzzle. Once you get into .30 and .357, or a high powered .25, a 2 inch body has the volume to quiet it down properly. Big bores in .45 and up move enough air that they need a long, large-volume body, and a small moderator on a big bore just won't do much.

Every listing in our airgun suppressor collection shows the caliber range it covers, so you can match it to your gun.

3. Think about length and weight on your gun

A moderator adds length and puts weight out front, and that matters more on some guns than others. On a bullpup or a gun you carry all day, a short, fat body usually beats a long, thin one with the same volume. On a bench gun it barely matters. Weight at the muzzle can also make a light gun steadier to hold, so it isn't always a downside.

4. Make sure it comes apart

Lead builds up inside over time. A moderator you can take apart by hand lets you clean it and check the baffles. A sealed one can't be cleaned, so lead builds up in it for its whole life.

Fitment: threaded, unthreaded and adapters

Threaded barrel. Order the moderator in your gun's thread and it goes straight on, no adapter. This is the best setup, because every adapter adds one more joint that has to be square to the bore.

No threads. A lot of air rifles come with a plain barrel. A slip-on airgun adapter slides over the bare muzzle, locks down with two set screws and gives you a 1/2-20 UNF thread on the front. Nothing gets cut or drilled, and it comes off with a hex key. It comes in single millimeter sizes from 10mm to 16mm, so measure the outside of the barrel at the muzzle with calipers before you order.

An odd thread or a specific gun. Some guns need a gun-specific adapter to get to a standard thread. We carry adapters for a number of common rifles and pistols, and the whole list is in our airgun suppressor adapter collection.

If you're not sure which of these applies to you, email admin@airguncapital.com with your make and model and a photo of the muzzle, and I'll tell you what fits before you order.

Looking after it

Every so often, take it apart, wipe the lead out of the baffles and the tube, and put it back together in the same order. Check it's snug on the barrel before a session, since a moderator that has worked itself loose can tilt off the bore.

Is it legal where I live?

Check your state, county and city laws before you order. Our collection page has more on this in its FAQ.

Common questions

Is a moderator the same as a silencer?

Yes. Moderator is the common term in the UK and Europe, and silencer or suppressor is more common in the US. LDC is another name you'll see. They all mean the same part.

Will a moderator hurt my accuracy?

It shouldn't, as long as it's square to the bore and the exit bore is sized correctly. Accuracy problems almost always come from a moderator that's crooked on the barrel or an endcap that clips the pellet, and both go back to the thread or the adapter. Your point of impact can shift a little when you put a moderator on, so check your zero after mounting one.

Does a moderator work on a springer?

It takes away the muzzle blast, but the spring and piston noise stay. Expect a smaller drop than on a PCP.

Can a moderator get rid of the crack?

No. The crack comes from the pellet breaking the sound barrier, and it travels with the pellet until it slows down. Drop to a heavier pellet or turn the power down until you're under about 1,100 fps.

Does a moderator slow the pellet down?

Not in any way you'd notice. The pellet passes through the baffles without touching them, and the barrel has already done its work by the time it gets there. If you want to know for sure on your gun, run a few shots over a chronograph with and without it.

Which one should I get?

If you're between two, email me your gun and the caliber and power you shoot, and I'll tell you which one I'd run.

← Older Post

Leave a comment